Clik here to view.
T-Rex 800 Pro DFC, first flight crash after fast roll oscillating
@webmotions wrote: Mechanic: T-Rex 800 Pro DFC with stock components.FMU: Pixhack from CUAVSoftware: Arducopter 3.3.3 After a few Seconds and only a few centimeters off ground, the Helicopter began to...
View ArticleFPV over telemetry
@lahva wrote: hello!! I need help with my hardware configuration. I have one F550 APM 2.6 drone with basic parts. So.... I want buy telemetry and i need know - can i make somehow FPV over telemetry ??...
View ArticleClik here to view.
X, y and z in phase vibration on trex 450
@michelzrk wrote: Hi guys! I am working on setting up ArduCopter on my Trex 450 Pro V2 (KX015080AT). After tunning the gains I could fly it on Stabilize mode. But before turning on Loiter mode I...
View ArticleClik here to view.
Trex 450 need help
@ivank wrote: Greetings to allI was wondering can someone with experience can take look at my PID settings.Heli hovers great in stabilize mode but when i make right yaw stick input tail bounces and...
View ArticleGX9 high speed tests in AUTO
@tridge wrote: Hi Rob,We got the GX9 to 32m/s maximum speed in AUTO today. Logs are here:http://uav.tridgell.net/GX9/2016-04-25/30.BINThe final step to getting rid of the pull-ups in the turns was to...
View ArticleT-rex550L modified 600E CUAV Pixhack Stable Loiter
@zhangsir wrote: My T-rex550L modified 600mm main rotor, 6s battery power, based debugging after the third flight, the state is relatively stable, PID also requires more detailed debugging. Test Video...
View ArticleClik here to view.
RX+Pixhawk+FBL How to connect ？
@zhangsir wrote: IMG_20160512_195808.jpg1280x720 302 KB Why not start Kbar FBL it? Posts: 4 Participants: 2 Read full topic
View ArticleSwitching to loiter causes the baro to drop 10 meters
@Jman841 wrote: I am using a Logo 690sx in traditional helicopter and had tested and flown in stabilize, loiter, and auto in the past without issues. Yesterday I flew it and when I switched to loiter...
View ArticleArducopter 3.4 TradHeli Support
@Rob_Lefebvre wrote: Hello all, I just want to make it clear, I am no longer able to support TradHeli releases starting with AC3.4. This has occurred because of 3DR discontinuing support of AC...
View ArticleAPM 2.7 Trex 450 fly bar serious up / down oscillating and crash
@keeyen wrote: Anticipating venture into traditional heli as a main VTOL machine, I learn to set up my old Trex 450 with APM 2.7. I manage to set the rate roll / pitch and yaw and use other parameter...
View ArticleTrex 250 with APM
@zcemsia wrote: Hi guys, Im a newbie to the apm platform, and have run into a few issues. Im using an apm 2.6 with v3.2, and mission planner 2.0 on mac osx. I have all the swash servos working however...
View ArticleHeli servo output problems
@ThomasH wrote: HelloI've started to setup a 450 and a 500 with APM 2.6. I think i've connected input and output correctly. Unfortunately I cannot get the input signals to move the correct servos. Ch2...
View ArticleRudder input affects swash
@metori wrote: Hi all. When I turning rudder stick on transmitter then swash plate turns lightly. All this in STABILIZE mode. There are no issues with swash in ACRO mode. Can't find anything relating...
View ArticleMotor Interlock Enabled
@Usamah wrote: Hello guys. I am new to RC autopilot. I just finished building my GAUI X5 Helicopter and I am trying to integrated it with Pixhawk Autopilot. As I finished with all the calibration...
View ArticleUnable to set the servo configuration, Help needed
@Maaz wrote: Hello, I am using Pixhawk autopilot on a Raptor G4, fuel powered, Flybar system. The problem that i am facing is that i connected the servos in the "main out" of the servo rail in the...
View ArticleClik here to view.
P9x v1.1（PX4v2 Mod） and SAB URUKAY 3 ArduPliot AC3.3.3 FW Loiter Mode success ！
@zhangsir wrote: 9Dsmart P9x v1.1（PX4v2 Mod） and SAB Goblin URUKAY 3 3-bladed ArduPliot RC Helicopter Loiter Mode success ！ 3.jpg1280x720 119 KB 5.jpg1280x720 244 KB 2.jpg720x1280 453 KB 4.jpg1280x720...
View ArticleDownstream FBL controller from DIYDRONES blog post
@InvertedCNC wrote: Greetings! I just stumbled upon this article on DIYDRONES about an RC pass through to allow use of a traditional FBL controller...
View ArticleStock E-Sky Belt CP v2 with AMP 2.8 IS IT POSSIBLE!
@ivant wrote: Hello, I've just repaired my Stock E-Sky Belt CP v2 with 6ch transmitter from crash. Now i want to use AMP 2.8 with ardupilot in stabilize or AltHold mode to assist me until i am...
View Article700 class gasoline heli
@hirochi_hirohiro wrote: Controller Pixhawk(AC3.3.3)GPS M8NTelemetry Xbee(2.4GHz)Engine OS-GT15HZ(25:1)Throttle controller Futaba GV-1 Stabilize OK.Alt Hold OK.Loiter OK.PosHold OK.RTL OK.Circle...
View ArticleClik here to view.
450 heli multiblade with Apm 3.1
@IcescuI wrote: Hi all,im setting up a trex450 with apm 3.1, i would like to install pixracer in future but apm was in the drawer...the multiblade head is phased at 90 degrees, someone knows if i...
View Article