Clik here to view.
RPM problem, what's the problem?
@Ricoman wrote: The hall sensor operation for RPM monitoring is finished. RPM monitoring is smooth. However, RPM monitoring becomes impossible from any moment. RPM maintains 6000 From a certain point,...
View ArticleRC Feel parameter?
@Pakman wrote: Hello, Tuning guide mentions RC feel parameter. But I can’t find this parameter in the parameter list. Although there are sliders corresponding to this crispness/sluggishness. To which...
View ArticleHeli 3.6.9 Alt-hold parameter settings different from 3.5.5
@rfine7666 wrote: Thanks in advance for any help. Question in Heli 3.5.5 and earlier versions to use alt-hold we often had to set the parameter Accel_Z_P to around 0.2 from default of 0.5 to prevent...
View ArticleAnyone using a 2s 7.4v battery on a Pixhawk 450 Helicopter
@rfine7666 wrote: Thanks in advance for any help 3DR Pixhawk, 450 helicopter, 3800kv motor, Emax digital servos, Currently I am using 3s 11.1volt lipo batterys on my helicopter. Wanting to know is it...
View ArticleClik here to view.
T-rex 700 unexpected crush
@AdHd22 wrote: Hello everyone! I’m new in heli (used to fly drones but i’ve wanted to try something new) and together with my friend we’ve built T-rex 700 on 12S Li-Po with three blade head. We were...
View ArticleClik here to view.
If there is a problem reading the RPM, what is the cause?
@Ricoman wrote: Hi I’ve asked similar questions in the previous installment. In this case, Chris told me that a bad sensor was the cause. I prepared a new gas. This is set to RPM 9,000. However, B_LOG...
View ArticleClik here to view.
Trouble with Loiter and Dual GPS
@Steve_Mitchell wrote: After more than a two year break from RC flying and Ardupilot. I thought I would drag out my old gasser Goblin 770 and try all the cool new features in Tradheli. Thank you...
View ArticleAn upgrade for my helicopter, a curiosity about temperature sensors
@Ricoman wrote: Hi I bought a new RPM sensor, throwing away the “bad sensor” that Chris once said. While I was looking for the RPM sensor, I found a Temerature sensor. The engine of my helicopter now...
View ArticleIs it possible to replace the Futaba R7008SB?
@Ricoman wrote: Hi. I still have not solved the problem of temperature monitoring. So I thought. My controller is T14sg. The futaba’s R7008SB is equipped with a temperature sensor that allows...
View ArticleFC does not work
@Ricoman wrote: Hi I bought a new engine this time. I am glad I installed FC but it does not work. During setting, fc does not respond suddenly while moving servo by rc. GCS can not get any response...
View ArticleCompass mandatory?
@twistedwings wrote: Do stabilize and acro flight modes work without compass? Posts: 3 Participants: 2 Read full topic
View Article450 Heli vibration
@Carpette_Stunt wrote: Hi everybody! I have a 450 Walkera with an APM 2.6 with 3.2.1 copter firmware. And I can fly it but it’s really hard. The copter vibrate a lot and there is too much expo in the...
View ArticleQuality of QGC App and Radio Remote Control in Auto Mode
@zhangsir wrote: Yesterday, during the automatic mode of testing CUAV V5 nano Alzrc 420, the QGC gcs of version 3.5.3 was used, and the virtual joystick was opened. The task was edited on QGC and...
View ArticleCorrect RPM measurement
@Ricoman wrote: Hi I have previously asked about the unstable appearance of RPM sensors. I heard about the bad sensor and I ordered a new sensor. Futaba RPM sensor … very expensive But I bought. There...
View ArticleTransition from stabilize to alt. hold mode
@arpakorn wrote: Hi refer to my set up mini pix for helicopter. when I switch from stabilize to alt. hold, the swash plate tilts a lot and collective pitch keep dropping. The above test is done as...
View ArticlePreparing for Autonomous Takeoff and Landing with TradHeli
@JoshW wrote: Hey there… So, with help from the Wiki, the tuning guide, and @Leonardthall I’ve got my 700E flying very well in AltHold, Stab, Loiter, and Auto. I’ve got Auto missions running at 25m/s...
View ArticleAcceptable amount of VFF setting with Heli 3.6.9
@rfine7666 wrote: Thanks to all in advance for any help Using 3DR Pixhawk with Heli Ver 3.6.9 on a Hobbyking 450 FBL heli, what is normal or acceptable amount of VFF parameter setting I can use? Right...
View ArticleAre there any conditions for changing flight mode?
@Ricoman wrote: Hello everybody. I have come up with a little complicated problem this time. This is a problem I had since I started the helicopter. I used pixhawk to create fixed wings, quads, hexa,...
View ArticleOdd swash behavior
@MephistoPFBR wrote: Hi guys Please forgive my english. I will do my best to make myself clear I build a trex 450 pro for test and tryout purpose before my dominador 550L Parts: Trex 450 pro DFC...
View ArticleTail Bouncing Issue
@rotems wrote: Hello, I have a Trex 700 with Pixhawk 2.1 and when I’m flying in Loiter mode the tail is bouncing up and down during forward and backward flight. Maybe someone know what could be the...
View Article